HFX868 Transmitter with built in Lithium Polymer single cell charger. The HFX868 tx has negative expo, V-tail, and normal mixing modes. Full proportional 4 channel output. 3 user-selectable frequencies. FMS flight simulator input jack is ready for the FMS flight sim cable available separately. Built-in buddy box jack turns your Hitec or Futaba into a 868MHz transmitter.

Available in two versions: for charging 5mm Bahoma cells (e.g. LP20, LP30 and LP50) and for charging 10mm Bahoma cells (e.g. LP90, LP130, LP200).

The HFX868 is available only in Mode 2 (throttle left). Download the HFX868 user manual.

FMS computer interface cable for use with HFX868 Transmitter and your own PC RS-232 Serial Port. FMS Freeware Simulator CDROM is included at no charge (Freeware). CDROM also includes good Plantraco videos and FMS models of Plantraco RTF airplanes.

Now you can fly your models with your HiTec or Futaba transmitter. The Monolith will convert your Futaba or Hitec transmitter with a din6 socket into a 868MHz transmitter compatible with all Plantraco receivers. Just plug the Monolith's DIN6 plug into the buddy box trainer socket. Calibrate once and you are ready to fly.

A 4 channel actuator receiver: 3 actuators and a built-in 2A ESC. Works with the HFX868 transmitter and the Monolith buddy box module. Weighs 0.95g including the patent pending Bahoma connectors and actuator/motor socket connectors. Built-in low voltage protection: motor speed reduced at 2.7V.

Works with the HFX868 transmitter. This is the most user friendly Plantraco receiver, weighing in at 0.9g including the patent pending Bahoma connectors and .05 pin and socket connectors for 2 actuators and 1 motor output. Pure Digital Radio Link, Built-in low voltage protection.

This is Plantraco's lightest receiver, with the added bonus of the Bahoma battery system - weighing in at approx 0.38g. This receiver has no MicroConnectors but it does have 5mm Bahoma magnets. Output for 1 actuators and 1 motor. Pure Digital Radio Link, built-In low voltage protection. It is suitable only for those who can solder very fine wires.

At 1.1 grams, the lightest servo capable micro receiver. This receiver is rock solid pure digital. Smooth action and good range for your Micro R/C models.

Designed for use with WES, Blue Arrow and Falcon 1.6g servos using "mini-JST" plugs (JST-ZH). Built-in 2 Amp motor speed control, brushless ESC capable. Glitch free reliable micro R/C.

The MiniAct weighs approx 1.1 g and provides ample power for most indoor R/C aircraft. The Nano Connector plugs right into the Micro9 receiver - very good for beginnners - plug and play!

The MicroAct weighs approx 0.4g. It as 16cm (approx) leads with nano-connector - plugs right into the Micro9 receiver. This version of the actuator can be used in hinges and has plastic flanges under the base to fix to rudder or elevator if desired.

Hinge Actuator: at 0.23gm this is the lightest pre-assembled magnetic actuator for micro R/C flying. Wire leads are about 18 cm length and require soldering onto the receiver pads. Self Centering. Torque vs weight ratio is good! 150 Ohm coil, 0.06mm copper magnet wire.

The lightest commercially available actuator but requires assembling into the control surface. Resistance 75 ohms, weight 0.07g, I.D. 3mm, O.D. 3.8mm. Supplied as actuator coil with 12cm leads and separate 2 x 1.5mm N50 magnets.