Ultra lightweight slofly wheels - supplied in pairs

Sold in pairs, Mini Lite Wheels are light & feature a 2-piece press together hub and a super light foam wheel. Comes standard with 1.2mm axle hole and can be drilled out for larger diameter axles.

A lightweight foam tire and sturdy light scale plastic hub. Supplied in pairs.

A small tail wheel suitable for park and indoor flyers.

Why scuff your tail all up when landing? Micro Tail Skid comes with two pins molded on flat for easy installation and secure gluing. Keeps the tail section of your plane from dragging the ground

Now your tail dragger can have a tail wheel bracket. The two piece bracket simply glues together to secure pre-bent 1/32 wire tail wheel strut. (the tail wheel in the image is for illustration only).

Ideal for Park Flyers! Lightweight aluminum design (0.25g) allows for up to .047 (1.2mm) wire. 2-56 machine screw securely locks wire into place. Press fit the Mini E/Z Connector into a Mini Servo Arm for a secure and dependable fit. 2/pkg.

Closed loop surface connection gives you precision control! Complete with 4 DuBro Mini E/Z Connectors, 8 aluminum crimps, 10 feet of 10lb. test no-stretch control line, & 4 micro adjustment pins - enough for rudder and elevator. The Micro Pull-Pull System weighs 2.2g.

Comes complete with (2) 20" .032 pushrods, (2) 18" pushrod housings, (2) Micro E/Z Links (90 degree bend is already on pushrods) and (2) Mini E/Z Connectors. Ideal for indoor and park flyers.

The Micro Control Horn measures 1/2" in height and comes with a pin molded on the bottom flat for easy installation and secure gluing. Pin can be trimmed off if not desired. Ideal for indoor and park flyers. 2/pkg.

Snap fit on .032 wire (0.8mm, 21swg), simply bend 90 degree angle on pushrod and install E/Z Link onto pushrod (No Z bend required). Super lightweight design, ideal for indoor and park flyers. 4/pkg

Micro aileron system designed for indoor and park flyer aircraft. Complete with Micro E/Z Link (2), Micro E/Z Connector (2), 1/32 (.032) push rods (2) with "L" bend wire (2), and plastic bearing (2). The ideal set-up for installing ailerons on your aircraft.

Mounts inside wing for use with ailerons and control linkage systems. Bellcrank injection molded and comes complete with mounting hardware.

The Dubro Electric Flyer Hinge Tape (actually a roll of BlendermTM) has great adhesion characteristics and is easy to remove. In addition, the hinge tape will not leave residue. Supplied as a 15ft roll.

Sig EZ Hinges are the simplest hinge around for installation with cyanoacrylate. Cut a thin slot with hobby knife or hinging kit in each control surface. Join the surfaces with the hinges dry. Apply thin CA along hinge/surface joint. Done! Suitable for all models. 24 hinges per package.

The Micro Clevis comes complete with removable .031 L-shaped clevis pins. The silicone tubing securely holds pin in place. Includes threaded coupler for .032 wire, which can be soldered or glued with cyanoacrylate. Extra pins included in package.

Replacement pins for Micro Clevis - 12 in packet.

Servo arms long enough for the extra throw needed on the electric 3D airplanes! Micro Servo Arm XL includes (4) single arms & (2) double arms. Made with special attention to weight, strength and performance. Lightweight 100% virgin nylon arms stand up to the stress of 3D aerobatics. Each arm measures 1" from center to outer edge.

A low profile design with a small spring-locking latch suitable for any doors, hatches, panels, etc. The Hatch Latch is secured in place using CA (cyanoacrylate). The unit is approx. 1" long x 3/8" wide. Can be painted.1 per pkg. (0.75 grams ea.